Application scope:
Vulcanization tank is mainly used for rubber tire retreading,
reclaimed rubber desulphurization, wire, cable, tape, rubber
rollers and other rubber products vulcanization. styrene-butadiene
rubber thermoplastic refining, wood, Chinese medicine
sterilization, oxidation of aluminum products, carbonization of
bamboo products widely used in the gypsum and its products and
other materials autoclaving.
The features of the autoclave for tyre retreading:
The autoclave for tire retreading is a pressure vessel with speed
open door, the autoclave openings sealed with inflatable silicone
ring or internal pressure self-tight rubber pad. Mechanical or
manual gearing is used to lock and open the lid, reasonable
structure, convenient operation, good sealing performance, the
temperature in the tank is uniform,furthermore, complete safety
accessories (equipped with safety interlock device).
1. Introduction
1. Vulcanizing pot design and manufacture in strict accordance with
the national standard of "" steel pressure vessel, and according to
the country" pressure vessel safety design review project "the
relevant requirement of inspection.
2. According to the heating mode can be divided into steam
pressure, electrical heating and heat conduction oil heating three
forms.
3. According to different division control circuit for PLC control
and PLC control add touch screen display two kinds.
2. Equipment features
1. Tyre renovating lower the production cost
2. Can be devided into single or multiple tyre vulcanizin
3. Warming up, vulcanize time, pressure, aerate, exhausting are all
automatic control
4. Temperature in the vulcanizer is evenly, balance control of
every single tyre pressure, ensure the hardness, strength,
elasticity of the product no deformation
5. Opening door adopt safety interlock, have passed the
identification by Provincial Technical Supervision.
3. Operation
Manual closing, vulcanizing pot after is open, the power is
connected by hand motor door-close button, vulcanizing pot began to
enter into automatic control.
1) miniature cooling motor startup
2) the circulation fan startup
3) heater or steam heating begin
4) vacuum pump start-up
5) 0.75 M afraid of filtering dry air valve opens(into the cans of
compressed air should be no oil dry compressed air) until
vulcanizing pot pressurized to setting value, to date, heater,
self-control after fan, EPS value to package sets the set pressure
value will suffer. Vulcanizing pot in which meets the above
conditions launched. After timer General vulcanization time is
2.6-3 hours. Achieve time vulcanizing pot automatic vent, until the
compressed air all platoon tank to tank clean, pressure value zero,
open the door motor automatically start make pot the doors opened,
as the entire system without electricity, vulcanization ended.
4. Technical parameters
| Item | 800 | 1200 | 1500 | 1700 | 2000 | 2600 |
| Inner diameter(mm) | 800 | 1200 | 1500 | 1700 | 2000 | 2600 |
| Canister length(mm) | 22000 | 3000 | 3000 | 4000 | 4000 | 10000 |
| Number of lid sawtooth | 12 | 12 | 14 | 14 | 16 | 24 |
| Thickness of lid (mm) | 10 | 10 | 10 | 10 | 16 | 14 |
| Thickness of the tank body(mm) | 10 | 10 | 10 | 10 | 12 | 14 |
| Working pressure(MPa) | 0.8 | 0.8 | 0.8 | 0.8 | 0.8 | 0.55 |
| Dimensions(mm) | (length*width*height) | 22766*1445*1170 | 4010*1575*1670 | 3960*2150*2050 | 4925*2162*2070 | 6200*2590*2424 | 11722*3360*4136 |
| Weight(Kg) | 5580 | 2017 | 2950 | 3835 | 6500 | 16775 |
